Awsome YoYo,
I cannot believe how close it is... look great!!
yeap, like I was saying, the Select are thin, thiner that most of fins, and pretty sure more that the Ka!
Now I think we are in trouble
It is great for Lao to have both, it give him some variations, be able to use the Ka with a bigger board.. I heard he bought one... cheapo
I can just imagine people now will playing with their fins
Thanks for sharing..
A selection of weedies and rough measurements
Top left elmo JP 40 something slalom to 29 470 143mm base 42mm widepoint 11-12mm width. Top speed 37 normal 34, lots of sessions, JP slalom II 84, 54 wide.
Top right yoyo kinetic 36 to 27 450. 128, 45, 11-11.5. Top speed 36 a few sessions, cut down 270 to 245, 51cm wide slalom board
Mid left elmo select lightning evo 35 to 24 450. 123, 42, 8-9. Top speed 42+ lots of sessions and close to 37 through chop, cut down 270 to 245, 51cm wide slalom board
Mid right Flying objects 26 450. 130,38,11. Top speed 38 in perfect conditions, not good in chop spinsout 33 ish normal lots of sessions. JP FSW91, 60 wide
Bottom left KA 23. 127,37,9. Top speed not tested.
Bottom right 31 to 22.5. 116, 34, 7.5-8 400. Top speed 36 one session. cut down 270 to 245, 51cm wide slalom board
Despite similar wide points 29% for all except the Kinetic and Evo at apprx 35% the thickness profile varies significantly. KA carries the thickness through to the tip more than the others. FO very thin in the trailing third.
Nice job and write up Sam,i just might rebox some Selects that i no longer use cos they were horrible.Not that we have much of a weed problem but could be good for an epic Swan bay session.
Mike! yes, I seen that fin close up! This is just manificiant work I say, you are such an artist
I have to say I am not that thin in the job in comparaison?
Buuut I have an escape way which I will explain soon... which is for me one of the key of rock stable speed weedfin!... some knows I am sure
Your fin remind me my Lessecher Duo 28 light wind fin
You could easy carry a 7.5, even a 8m on 110-20 board!
I would be very happy to try it Mike if you let me to!?
It make me want to make one too now.. something more performant that my Duo!
cheers Sam!!
the reworked drake(40) looks great!!
The story behind this fin is, it came with my original iso 105 and felt like crap as an upright slalom fin. i decided to make a weedy out of it prob 4 years ago.
i took to the leading edge with a flat bastard file and thinned it out to a point, touched it up with some 150grit and left it at that.
Although it never felt fast, it did its job as a weedy and to this day it NEVER!! let go.
Its great to see it being reworked by Sam. I have checked out a few of his fins and i have to say they all look great! he def has a great eye for it!
cheers mate.
The drake 34 that also came with the iso became my 22 weedy for my ca 40..at this stage it holds my 2 sec/10 sec/nmile and alpha pbs..it got the same finish as the bigger one.
might look at getting Sam to look at this as well..only kidding mate!
No worries Snides
The problem I have to work better that if its was mine
The fin will be perfect for your 54 board with a 6.5.. speed, I am guessing around 35, 37 maybe with a 5.5.. just guessing!
With the rake given @ 38-40 and 25.5, I would not venture too much in hards run with it unless a good tide
The simple way for a quick weedy is to take a 32cm Flying objects weedy, cut the bottom off so it is 23cm and file the rough bits, then after you hit a rock file a bit more off, this fin is good for 40 and rock solid
Thank you Kato, this is such an important subject I think.. I try, we try our best!
I think experiences and knowledge have to be shared...
Lao, nice to see all your weed weapons , I have no chance to pass you now, not like I did.. that cool to me
Your display is perfect, that will save me some photos for one of the most important part of what work and what not in matter of the design of the speed weedy!
The information I give here is like all the rest before, it is by what I found when testing, for my weight, my gear.. but pretty sure that will fit 80% of the people
It is for everyone, mainly for people that don't know about weedies! That will save you time and money (not like me, I learned the hard way!). Test made on choppy water, flat is more forgiven!!
We talked about the lenght, width base, the thickness, the surface area.. now I would like to talk about the shape of the area! Lot of us would have guessed already! I will use 0 for STRAIGHT, - for IN, and + for OUT, this is for the lenght of the fin.. remembe we are talking high speed weedy, 35+ and stability
ps: when I say 0/+ I mean straight for the first 3/4 of the leading edge, then 1/4 + curve closing!! I know my explainations sound a bit.. sorry
* 0 leading edge & 0 trailing edge WORKS, limited in high speed and spins >> 35+ kts like the JP above (had one in my early tests)
* 0 leading edge & - trailing edge WORKS, very limited in high speed and spins >> 33+ (amazed Lao you had 36 with the Kinetic!)
* -/0 leading edge & -/0 trailing edge WORKS, good high speed >> 40 tested stable with my special, can go higher.. don't laugh I ll explain later..similarity to the Flying object
* + curve leading edge & - curve trailing edge BIG NO, very very limited, 30-32 and spins
* + curve leading edge & + curve trailing edge WORKS, very limited in high speed and spins >> 33+
* 0 leading edge & + curve trailing edge, WORKS, good high speed, one of the best like the LAOs lighting >> for me around 36+, Lao 42+, was on flat was it?
* 0/+ leading edge & + cuve trailing edge, WORKS, good high wind, the best in my book.. like the LAOs Ka and Select >> 38+ with my SS ultra, can go higher. the Lao's select raked @ 35-37 given his thickness! would definitly be a killer
Dam Lao, you are a trouble maker!!
I will carry on tomorrow with some photos of few of my fins, some explainations, and the key of a rock stable speed weedfin nooh we not finished yet
mY 2 CENTS (I'll make it short)
Weed fins = Control
Why = More rake
Cost = less lift
Who will benefit most = Average to sub-elite sailors & and people that sail in v shallow, grassy or weedy areas
Starting to see your point Hardie. Through the years I'd noticed the odd sailor choosing to use weed wins in clear water. Very odd? Now I fear I'm turning into one myself. Lake Illawarra forced me to use one and now I'm not bothering to change the fin when I go seaside.
I think you notice the advantage when the nose of the board gets pitched up. A vertical fin goes into that point-first jousting orientation. Feels sketchy.
So what are the tricks to moulding new bases? What sort of brew do you pour in?
Surprised nobody has answered to Ian!!
Ian K: So what are the tricks to moulding new bases? What sort of brew do you pour in?
This is the way I do it.. make sure you add some fibre meshing!! not like me too many times
The self leveling boxing mould is made of silicone, and peels off sooo easy .. I just black marker the base when finished.. (you can use colors to mix)
Some people have some more fancy ways..
Some people use the powdered mesh with a chopped strand matt reinforcement, but around the barrel nut it's important that IT breaks if you hit something and not rip out the fin screw through the board.
just found my card reader Sammy!
The first image shows the rig and split mould
this next image shows a lessacher duo weedie reboxed at 38 degrees with a refinished surface and swept up trailing edge.
next is the reboxed choco 40 cm at 38 degrees with the same sweep at the trailing edge but the chord has been moved to 35 percent .
now for the last one, I've shifted the chord back about 5 percent on an mfc that was'nt doing so well, making it about 40, cut a bevel in the lower trailing edge (so if you hit something the fin does'nt cut a neat groove in your brand new board) and taken a nasty bend out of the fin itself. It's now ready for tomorrow
Great stuff Paul, it look great.. first time I see your jig!! Is it the same way that Elmo did his? I was trying to visualise his and could not quite!
He was talking about a back board with angles on it.. must be similar is it? You made a little anti-spin noch on your fin I see
For the people that still don't know the answer for "rock stable home made weedy @ 40" (I did give a hint early!) here it is:
Nooh it is not putting more rake to the fin! Add a concave the long of your trailing edge on both side "symetrical".
This is Claude's 40kts+ SS_WING 230/30, one of my early good fin made almost 2 years ago. I did exagerated a little the concaves, you don't have too!
I have not try on normal slalom fins under 30/rake. Some people going to say aaah I knew that, some will say why I haven't thought about it before!!
What I noticed is most of the slalom fins out of the shell does not have it!! They all have a nice long curve from leading to trailing, sometime so hard to see, it look almost flat.
I realised this about 2 years ago when playing with this chocking fin originaly not working more that 30 knts.
Anyway this is a Wo Duo, double-assy, it is when fixing it and playing with the concaves that I had the light!
Even the fin was bad (you can see all the work I put in!), it would not spin! This fin now is rock solid and drives @ 36, the force apply each side will force the fin to drive straight. I only finished it 6 months ago!!
Because it's 11mm tickness I cannot go higher in speed.. I may have to get it tested by a big boy in the team
To finish my bla bla in this topic I am only going to show you parts of my SS_Special experimentation which took me to 40kts and explain the idea behind.. sort of!! we don't laugh please...
Here some mesurements so we have an idea: 225/40, 117mm wide at the base starting @ 10mm thick to 3mm @ 30mm from tip (my thinner so far)
I took the idea from my Tectonic "Gold Wing" 34, nooo I could not just rake it, I would loose the angles, the area, too thick at the base (11mm), etc..
So I modified the angles to make it fit to my fin!! This is my 3 speeds fin.. Actually, YoYo and Lao was not far of with the Kinetic (I want to apologise guys.. I was thinking about - curve, you have -/0 followed by + curve)
Some will think it is like the FO.. well, not at all, the FO has - curves then + on the trailing edge (I don't like - curve), also it has a + curve on leading edge (which work for some, definitly not for me), and it is too thick anyway..
With the wide base & 10mm thickness & 20% of concave, the fin goes upwind like a charm even with his 40% high point! You can see how smoove is the entry point..
When travelling and accelereting, the fin pass from the first part | / of the fin to the 2nd part / /, as you accelereting more and going down hill you pass to the 3rd part | /
Between the 1st & 2nd part we have eliminated some area, the fin can go faster.. between the 2nd & 3rd the fin become thinner and we add some + almost square to the fin which helps to drive the fin on the tip..
I like so much that fin that I made a 245/38 version.. not full tested yet
I want to wish good fun and experimentation to all , I have the feeling that we going to see more weedies around this summer
Thanks for the insights into the art of weed fin construction. Silicon moulds for the bases! Which got me thinking. How would you incorporate a bit of rubber into the fin base to allow it to flex right at the root of the fin?
The physics is overwhelming. 90 degrees ( talking in the across beam direction now not fore and aft) is not the optimum angle for sailing on a starboard tack. It'll be something less.
Though 90 degrees is a good compromise if you also want to sail on port tack, so it makes sense that that is the usual setting.
Keff: do you have problems with air bubbles in the brew ?
I do get the ocassionals ones, usually near the blade!
When finished the mix, wait 5-10 mins (you will see them forming,coming up), you have time.. pouring only takes few minutes. Try to don't mix too hard!
If still appear after.. take a needle and pop them out
To get rid of any bubbles just use a small blow torch.( what chefs use) This pops the air bubbles really well and give you a nice smooth finish.
Thanks Bendy, so simple never thought of it.. I will try
Great stuff Keef , thats a good idea.. I did actually found with all the moulds I made that you get more bubbles with the silicone, and they come later.. Just have to build a vacuum chamber now, that will help with the epoxy... cool
Ian K , I like the idea of the epoxy- rubber, I have been thinking about it for a while... since I saw Chris.L fins.. it look like he is using something similar!!
Is it stable when it drys? I means it does not shrink!
I would not mind having a crack at it.. Anything to add a mini knot to your speed is good
Maybe silly question but, I have not understood yet how you put the inserts in... you don't see them! Do you drill the blade and put them before? Anyone could explain?
I think Chris is using a sort of urethane. It goes off pretty quick though ~10-12 min. Used to get a fair few bubbles but I think he has it sorted now.
Boogie used to use a rubberized epoxy on his custom fins years ago and they were the cleanest bases you'd see.
Here's an easy to make vac chamber for de-gassing your epoxy after mixing
Its a length of 150mm drain pipe (5mm wall thickness) with 15mm acrylic end plates and foam rubber gaskets to seal the plates.
An 8mm tube bolt threaded into the acrylic serves as the spigot for the vac hose
I have another made from 300mm pipe which takes my gel-coated molds to de-gas them before doing the layup.
Got the lengths of pipe from drainlayers on a nearby building site.
I use the toughened rubberised epoxy mentioned by ice surf for my fin heads. It's called HPR5 and is available from Adhesive Technologies in Auckland NZ.
They may have an Aussie agent?
Its great stuff, you don't need any fibre , very tough and never cracks. Has the consistency of honey so has to be warmed up to use......quickly!
A spoonful of graphite powder mixed in colours the resin and makes the head slide in the box nicely when its all set.