Get my surfboards custom made by a local crew and about to order a new one.
However my last two boards have had delam issues on the front heel. I think from memory the board is usually 2 x 6oz glass all over or possibly just 6 0z with double layer on rear foot.
My latest board delamed in this area relatively quicker than the board before. The only difference between the boards is that i used wax only and didn't have a front pad. I'm not going to lie the board gets a hammering, strong winds, chop and a lot of aerial work etc.
So was seeking some advice or tips on this issue.
Current thoughts on reducing the delam:
- is compression related directly to delaminating?
- additional glass around the front heal
- do lower quality blanks increase the risk of compression and weakness of the glass bonding to foam? Do i ask my local to seek a better blank? Reason i think this, is a guy repairng my old board said the foam was quite powdery and didnt look of the highest of quality when he was sanding it down.
- add front pad to board (only reason i didn't was because it had a sick paint job and didn't want to cover it up :)
Thanks.
Try ordering a heavier blank. You can then use less glass.
The other thing I've heard is that the Hawaiian crew think that if you have a spray on blank it's more likely to have issues. Perhaps a tint is better?
We use lightest PU Blank with 6 x ply Stringer and glass With Epoxy and are own 6 oz clear glass with Carbon twine And boards a fine with in reason Delimitating can also be caused by blueming between coats of Epoxy and over use of hand laming Also have had no issues with tint or solid colours as long correct application between coats
Not trying to sound rude, and supporting local shapers and crew is great.
But, last 2 boards have delammed?
I'd be asking for a free board or at least a heavily discounted price on this one.
Or go to another shaper. They obviously have a process issue or no R&D/QA.
I'd say garden variety heel dent with poor foam that crumbled and gave the impression of delam?
ie: it might not be actually a delamination.....
Dunno about blooming/amine blush as surf epoxies are the least prone to it - and anyone who does not sand or scuff properly cured epoxy before another coat shouldn't be in the game.....
If it is delam, could be as simple as greasy hands ...... bit then you'd think rails not front heel but ya never know......
I just repaired a factory board where the bamboo delaminated- there was a little bit of vac bag bleeder left on the glass before the wood went on, of course it didn't stick to bloody synthetic wadding material.... retards.
You might be right Mark. Come to think of it may just be the foam is the main issue. Thanks all for help
You've had two boards by the same shaper delaminate in the same place, the second was worse than the first and you're about to buy another?
My advice would be to buy somewhere else.
Glass on pu just dents with no delam .composites on eps will delam and eventually crack.Epoxy /glass on pu is generally considered the best for strength and feel on the water but will still dent where your feet go.
^^^ but that's what I mean.
Is it even delam? Could just be foam degradation leading to a small space under the glass, and there never was a delam.
Before we talk about what cores do what, or offer advice, we need to know more.
But anyway I'd love to hear why you think glass delaminates from EPS more than PU? The bond is just as good......
Or are you talking about styro core itself cracking a few mm under the skin? If that's the case it is due to lower density EPS being not as strong as PU. Typically 28kg EPS vs 35kg PU...... you can't just glass it the same.
But the lighter EPS allows addition of wood, carbon, heel patches, PVC foams - all sorts.
A windsurf board with 16-18kg core and sandwich construction is WAAYYYY stronger than any PU board ever was ....... so you can't generalise and say "composites on eps will delam more"
Then for the other folks: Before we bag out the shaper maybe he had a bad batch of blanks and this info will be wonderfully helpful to him - if he is told. But not if the customer just gets the ****s and leaves.
Had a yarn to the shaper over the phone about my dilemma. He straight up told me that the blanks used for my boards differ from the standard foams they use. Reason being they sourced a heavier duty foam for my boards in the attempt to make them more durable. He said there maybe a risk that these blanks dsourced from a different company MAY not bond as well as the blanks they get from NSW. This added with the foam getting compressed and maybe heat to the board. Leaving surfboards in hot cars? Guilty as charged your honour. In fact I deliberately left my boards in the car to zap a bit of moisture out of fracture lines and dings in my board. Yeah yeah I know, what a muppet.
So to sum it up, board neglect combined with possible weaknesses in the blank used seems to be the issue. Not the glassing. Anyway I have good relations with the shaper. He is going to go back to there standard foams which he is more confident in. Hopefully a happy ending. Whether I agreed to use a different blank for my boards or not I can't remember but **** happens. It's my fault more than anything I'd say.
I like the boards.
I have been using the lightest Pu blanks available from SurfblanksAustralia NSW And have had no major problems Yes we do get denting depending on the rider But helps if have front and rear 5mm pads I have boards in Epoxy and Pol All you need is good Quality in Blank and appropriate materials and good glasser ??????????? Good luck