I recently decided to try my hand at kite surfing picked up a secondhand old kite (It is a best nemesis hp, maybe 2008 or 2009 model). Only issue, the 9mm inflate valve came off from the bladder. I have found some information out there that was helpful but some things I kind of just figured out. So I decided to put this up in the hopes it may help somebody out there. After consideration I decided to glue instead of buying stick on valves as they were around 25-30 bucks and I can use this stuff to hopefully touch up any other valves that need it.
After digging on this forum, the Internet and pretty much every store in my town, I decided to try sikaflex 291. It seems to be one of decent choices for gluing a valve back on. I got this from Bunnings for $21. I believe this stuff takes around 12 hours or so to set. Tried a few trade shops but nobody had any stormsure glue or something of that nature.
I lost the ball from inside the valve and could not be bothered digging through the kite to find it. You wouldn't believe how hard it is to find a similar type of ball. In the end I got a wooden 12mm bead from spotlight (they didn't have any plastic 12mm)
Taking some advice from the forums I needed something to put pressure down while it sets. I didn't plan ahead and found that the little sticky tape rolls are perfect size to go over the top of the valve and just put my toe hitch on top to put some weight on it.
As you can see I don't have a work space (living in a unit). I managed to pull the bladder enough through a zipper to lay it out. Again not having a work area or the tools I lay it flat on a Tupperware container on top of a foldout table.
Also, this is my first post so sorry if it's not in the right area. Also I'm only just a brand new beginner so hopefully my terminology isn't too off. I will check on it in the morning in about 15 hours (should be good by then), with the hopes of taking it out tomorrow. I will post an update on how it goes.
Great effort - but why ? $21 bucks from Bunnings and all of the hassles - vs $25 to simply stick on a valve and go kiting ?
Sure you now have a big tube of silaflex - now what ?
Just my 2CW ....
Keep innovating!!
Great effort - but why ? $21 bucks from Bunnings and all of the hassles - vs $25 to simply stick on a valve and go kiting ?
Sure you now have a big tube of silaflex - now what ?
Just my 2CW ....
Keep innovating!!
Lol
Yep glue comes in handy for bigger things other stuff many things bladders valves everything.i still think its cool though if yr other valves pop or come off
For reference rub it with acetone first chemical reaction between the two welds it .and not having a ball isnt the end of the world...
Hope it works for u
I use sikaflex aswell. Does the job, but aquaseal is the best.
Glueing a valve back on I do this:
Clean all surfaces when alcohol/methylated spirits
Get a spare square piece of bladder material - cut 1 cm hole in middle
Put glue around hole in bladder
Put glue on bottom and top of valve base
Put glue in an outer circle pattern on spare square piece
Put together and use cotton bud to move glue out evenly. Weigh down overnight
Make valve sandwich.
Credit to Ian
Great effort - but why ? $21 bucks from Bunnings and all of the hassles - vs $25 to simply stick on a valve and go kiting ?
Sure you now have a big tube of silaflex - now what ?
Just my 2CW ....
Keep innovating!!
Yeah as mentioned just above, it is an old kite and some of the other valves may need a touch up. The kite is about 7-8 years old. Will probably use the skilaflex around the place too. Also I'm not in a big city so I don't have access to everything. The stick on valves would be ordered online and take days to a week or so.
Just checked it and from first glance it seems to be sealed and bonded to the bladder quite well. I will take it out shortly to test it out
I can see by the bottom right hand corner of your valve mate, that's already peeling away!
What Troph said above is the way to properly do it.
ps. Who's Ian mate?
haha. From that 3rd photo I thought you were using to 5t press to compress the value. Shame it wasn't. That would have been funny. :)