Hey Guys!
I'm not new to this forum but not posting because most things are written and discussed.
But I didn't really found a thread about different Fin's and what they possibly have to offer.
Example:
I have a one board quiver, but the board is not so great Allround since there's a lag of performance in small mushy waves. I always loved quad setups so far, so this time I also went for quad. But I felt braked out. Like having a drag anchor under the board.
First thought, possibly my technic, the thick leash, the fins could possibly cause the problem.
So Ive changed to a coiled leash which not drags behind the board and mounted a middle fin instead of the quad rears. It was better but still felt a little bit sticky to the water and braking immediately if the wave is getting round in deeper areas.
Next thing I tried was a pair of twins with a knubster. I bought them for a short Sup I had earlier but didn't work good. This time it's a lot better. The board has drive now and is much livelier now. Later I dismounted also the knubster or trailer fin and it got even better.
The board still isn't a small waver shredder but the twin opens up a bigger range to use the board to low end.
But twins doesn't make every board better. And still most used setup is the trustee. And the quad is told to be fast accelerating and faster as the thruster, the opposite what I felt. And what would happen when some retro Keel Fin's where mounted to my board. Would I get even more drive and acceleration?
So I thought we maybe can dive deeper than the standard manufacture marketing talk and discuss if fin setups in general feel the same or depends it on the type of board which I use?
I hope you understand what I try to figure out, english is not my default language;)
??peace
In the distant past I prone surfed single fins then thrusters and twins, never liked quads as I felt they tracked.
Since I started SUP I've really liked the large US box tail fin and smaller side set ups. Reminds me of my single fin days. Like the speed of smik bonzer though.
Best surfer I ever knew was Evan Jones from the NSW south coast, he hand foiled his own and always used large twin fins. His opinion was multifins it wasn't the size of the fins but their position in relation to each other that was most important in controlling looseness/stiffness.
Jim Banks has some interesting stuff on YouTube.
(Im a intermediate only)
I have found that you need thin flexible fins so you can pump the board up and gain speed ,stiff fins I find are fast also but lots of drive and stiff ,harder to push on ,so its the opposite to windsurfing ,I like fibreglass fins for surfing with flex ,
I only use quads because my boards have wide tails ,some boards will suit other combos ,
After buying a board I try lots of combos to find what suits the board the best ,and also suits the wave and way I ride my boards ,then I usually stick with that combo .
So I have found front two fins flexible and the rear two slightly stiffer ,to give you the drive on the bottom hand turn .
You can over fin your board and it will feel like you are dragging something ,It usually takes me about 2- 5 surfs on one board
to find out what i like best, sometimes I come straight back in after one wave and change as I know straight away I have too much fin
and I cannot turn it as fast as I would like ,try a few fins and different combos until you find what you like ,it is a personal preference for everybody ,I hope you find yours .
Hi, could you give , board fin setup pic, brand n size specs . Fin box types.
This may help others with same to give their best working setups.
I'm similar to Tardy with fin trials .
and the feel of NAY / wrong / drag or YAY / WOW can be instant or MMMmmm... what wave do I want to try this on..
and with an asortment of fins have recently been working a pattern though my older boards ,
Disclaimer ; re board Fin boxs ;
only 1x Furtures of Quad n Center box , 1x FCS1 n center.
All others have; Center box with SMIK /Starboard/GEARBOX slot fin side boxs
that will exchange Twin Tab, Hanalei and other longer base fins in Front and Rears ,
Starting with Singles, 11" then working down, 2 n1 mixes, Quad / reverse Quad mixes, Big Twins only / Keels / Twins with trailers.
Thin fins, Fat, foiled, deep foiled, raked, pivot.
Extra Cant can be a hiden turning Gem , but can be wild when pumping from the nose on some boards
For slower, fat or small waves ; 2n1, small Extra Cant sides with Pivot Cutaway , XL Twins,
or Quad, small Extra Cant fronts with rears Pivot S to L, is loose or stepup to, L - XL Flip Tips or QUOBBA rears has more drive/ hold with quick turns.
ENJOY
Thanks for all your answers.
Of course ive to work my technik but who doesnt if not a payed fulltime waterman.
My Boards mostly had all FCS II. Only the very first F2 (US, FCS) and scnd Coreban Vibe (Futures) had other boxes.
The following boards where all Gong from france.
There was 2x the MOB 7'6'' one 105L one 120L which only worked as quad because the wide tail as tardy said. The 120L had the thruster option the 105 was 1 Generation later and the Centerbox was gone. Ive used FCS II MickFanning Fronts L and Carver Glas Flex Rears(flat). I had drive and loseness and did not felt anything bad about the fins. That's why i kept the fins because i thought it would work best for me and it would always stay that way.
Next one was a Zero 9'0''. US Center Box FCS II Side Box. Ive never tested the orig. Gong 9isch Center Fin. Ive mounted a Harley Ingleby 5.5''
and some sidefins. Ive played with Center Fin Position, worked best in the front third of the box. I had enough drive to go through lulls could go radical and fast in control, was able to slash a backside topturn and that all with a longboard. Really a great board, stable easy going and surfing limited only by its pilot. I miss this board and would direct take the same fins because it felt just right for me.
Then I wanted something light and compact with no swingweight for the "good" days when no chop and minimal wind so I got my hands on a Fatal 7'4'' 108L. Immediatly the bad awakening, I had to start in deeper section and lulls are not easy to go through because I had much less glide now. When you read marketing of fin manufacture you get the idea twins could be the answer because of sooo much drive. Tested once AM Twin with trailer, felt wrong. MF Thruster Setup mounted, was the best choice. Board is in Sweden now. Miss it a little but, because I had alot fun on Vacation at beachbreaks in france. Surfing atlantic ground swell instead of baltic wind swell makes of course the biggest difference, thats why most watersports adicted people have a board quiver and not one board for all.
Now I have a Karmen 8'4'' one board quiver (lol) classic outline much more rocker, much thinner tail, 5 fin option. Because I've done well with the MF's up to this point, I tested them on vacation in France. We had good waves and you immediately noticed that something was different here. I couldn't tell directly if it was the rocker, outline, thin tail or fins. But I could only change the fins so I tried. MF Front - Performer Rear, MF - Carver Rears 50/50, MF - Carver Sides (flat), MF Thruster, Performer Quad, Performer Thruster. By my standards the waves were very good and had power (10 -15sec).
On vacation I noticed that the Quad was slower and very raily. Back home in the onshore slob you feel it 5 times more because you are riding in the lower limit range. Anyway, I've tested the Karmen so far with:
Quad - sticky, raily, like having a huge bush of grass draging under water on the leash.
Thruster - similar to Quad but noticeably better in all aspects, very controlled, maybe best option for punchy fast atlantic waves
Twin - completely different board, fast, free, easy to edge over, handbrake released
Twin + Trailer - Like twin but less variable, probably better for more control
Keel retro(no Name China) - still on the way to me, hope for more drive but more control than twin, still variable as no trailer needed.
I cant test Single Fin and 2+1. Reverse quad (u mentioned fronts and rears changed (or turn the tip foreward))should also not work in my case, because I think the rear sides in general are the brakes (perhaps to much toe and/or cant). How do u get extra cant? Do u customise your fins? Making fins shorter is easy as breathing but adding cant should take some more brain and tools. Unfortunately FCS doesn't give very precise specs of their fins, so how do you know such precise data? Any Suggestions for flexi Twins?
Now I've talked a lot about the boards, even though I wanted to avoid it. So let me remind again, I want to know more about what you can get out of fins instead of talking about weaknesses of boards or their alternatives, because there is a excellent thread about small wave SUP's already here in the forum.
So good so far, best regards!
I like quad setups and I find that I prefer larger front fins. When I first got my 8.8 Spice my first session was on the stock Starboard carbon fins (4.7" front, 4.5" rear). They felt great in the 3-4 foot conditions. But after the swell dropped a few days later the board felt a bit dead to pump and generate speed in 2-3 foot conditions. I also didn't like the fact that a board with FCS II boxes came with FCS I fins.
So I bought a set of larger MR FCS II twins and a quad set of AM FCS II fins. I run the AM fins on the rear and they are about the same size as the stock carbon 4.5" fins. The board feels much more alive and happier to generate speed. I use the MR fronts day to day, but once it gets to over 5 foot, I switch back to smaller AM FCS II fronts, which are about the same size as the 4.7" Starboard fins. The MR fins felt great in 3-5 and I haven't tried them yet with anything bigger. I probably should try.
You can see here how much bigger the MRs are in comparison to the Starboard 4.7" fins. I think they are about the same size as the 5.5" Starboard fins. I was too lazy to dig out the carbon 4.7" fins from the fin wallet in my car, so I am using "armacore" Starboard fins for the comparison, but the shape and size is the same as the carbon ones
My 8' Hypernut came with 5.5" fronts and 4.5" rears. I broke one of the fronts (I have a bad habit of doing this) and the 5.5" fins weren't in stock. So I bought the biggest FCS I fins I could find in my local surf shop without realising how big they actually are. They are comical in size, but I really enjoy them on the Hypernut and I find that they help me to drive out of a bottom turn and the board feels great in the 1 to 4 foot range that I normally use it in.
I suspect that my preference for larger front fins could be related to my size.
Board : Smick spitfire 7.10" x 27"
Fins. : Rob Machado Seasiders Quad
Rider. : 80-82 kg , 62yrs, heavy back foot surfer
These quads combined with the smick spitfire are a dynamic duo, by far my favourite fins in waves faces up to roughly head high. They are a fair bit thinner than the fcs2 carver, performer as I had those ( not for long coz they crap ) because they're thinner they have some flex which I attribute to their performance characteristics, I'm no fin expert but I know what works and these babies work for me.
As I owned/own also these boards, I can share some info.
Note that ONLY use quobba fins. The extra top speed (I'd say they provide about an extra 5% to your surfing speed limit) trumps anything other fins can offer for my personal taste.
After reading your experiences it seems, good to have larger front fins when its slow, round, mushy and the opposite when waves are fast, steep and pumping. The rear fins, i guess, seem to to be able to add control, loosnes, pivot or railed feel to the board. So thank you all so far.
I have now received the retro keels from china. The workmanship is not bad at all. They fitted cleanly into the board straight away. I'm curious to see how it works. Definitely a lot of fin than, but I think it looks harmonious on the board.
I made some comparision Pics. Maybe someone is curious how big they are.www.seabreeze.com.au/img/photos/stand_up_paddle/20784488.jpg' />
Thanks for the FCS Specs Link. Good to know that there is a table for this. But it seems dates like cant and toe ive to get somewhere else.
Anyway.
Then ive found a video on Youtube i would like to share. I think if i found that earlier, then maybe i wouldnt have asked here.
Talking about fins.... I would really like to find a US fin box to FCS II adaptor. Does such a thing exist? The one made by FCS seems to be for FCS I only.
Yup, that's what I meant. Thanks Hoppo.
I want to put FCS 2 fins into a US box on the board. It annoys me no end that I have FCS 2 side fin boxes but the centre is a US fin box, so I cannot use a full FCS 2 thruster set. Instead I have to use the Starboard centre fin.
Well, you can route FCSII tabs on a fin to the FCS 1 dims, and then use the adapter.
FCS 1 and II tabs are the same width and depth, so it is easy to do, only cut/sand the outline.
I did this on these keels that were available only in FCSII. I wanted to try them on a board with only FCS1 boxes for testing a twin fin setup but with boxes too forward (thruster/quad setup), as they were the fins with the largest offset to the back.
The original:
After my cutting:
Thanks both. Colas, that seems a bit too irreversible for my liking. It's a bit pricey, but I am willing to take a punt on that adaptor from a Greek site.
The first thing you need to do is find out what fin set up you like ,as board shape matters ,then play around with size and stiffness ,
I also do what colas does I shave a bit off then to get the right size and feel ,Ive just brought some large quad rears ,and i will shave them off no doubt ,
eg,smik twins work as a twin because you have a very narrowish tail and seems to work like a fin digging in , ,wide tails better for continued speed ,more suited to quads ,and personal choice ,but do and can bounce on BIG waves ,thats why you need a gun
you mentioned some quads you used where draggy ,that because the profile or thickness of the fins ,so buy a quad set as the fins are
thinned down as to allow for less drag ,Quobbas have managed to increase speed of their fins and eliminate drag ,but I still felt they where stiff for very tight turns ,so you need to get smaller sizes ,but then my wide tail boards the fins would lift out on really sharp turns ,and i spun out ,so Ive gone to longer fins but flex ,it suits me ,this bit of info probably didn't help ,but something to think about ,
heres a picture of how much your side fins lift out at times ,another reason why I like quads ,for my wide tail boards
This set up is working really well in my Infinity V2Blurr..super fast and manoeuvrable. Thanks BigHug for the Quobbas! Mikey February twins and a small Quobba as a trailer fin.
So Baltic, you didn't mention a single fin. By allarounder I usually think rounded nose. My board with a round nose works great as a quad in winter surf but now as the energy lowers I have just put in a small 7" cutaway/hatchet single fin for the summer. Loose and fast.
The boards in the mid range of my pointy noses work best as thrusters though it took some years to figure that out. My smallest board is for hollow waves and the shaper only put quad boxes in, no choice and works great. My longest board is my gun and after years of a 2+1, large center with small sides and feeling stagnated I switched over to a large quad set this winter and just love it.
Enjoy your surf life.